An AURUS touch panel is similar to the other TELETASK touch panels. In this section we go deeper into all the specific settings.
Advanced tab
- Orientation
- Available on AURUS-2, AURUS-4XL and AURUS-OLED. Here you can choice between 'Default' and 'Rotated'. This way you determine how you will mount the touch panel horizontally or vertically.
The default state of the AURUS-2 is with the two buttons horizontally positioned.
This setting can always be changed. The configured functions of the buttons won't be deleted.
Pay attention: Always check if the notes are displayed completely on the AURUS-OLED. By turning the AURUS-OLED the positions of the icons and the notes will change.
Check this in the 'Edit this screen'-menu.
- Display Brightness
- Only available on the TDS12064. Switch between High (default), Medium or Low. In a bright environment it is advised to keep it on High where in a rather dark environment (e.g. bedroom) it is recommend to set the brightness on Low.
- (OLED) Display OFF after
- Only for the TDS12022, TDS12032 and TDS12064. Here you can change the default 15 min from 1 to 60 min (6h for TDS12064).
Be aware that increasing the time the AURUS-TFT is ON will decrease the display life time
- Feedback LED’s ‘ON’ brightness
- you can choose between ‘Maximum’ (Default), ‘Medium’ or ‘Minimum’.
- Feedback LED’s ‘Night illumination’
- you can choose between ‘Maximum’, ‘Medium’, ‘Minimum’ (Default) or ‘OFF’. It can be wisely to change the Night illumination to OFF in a bedroom.
- Feedback LED’s OFF when OLED if OFF
- Only for the TDS12022 and TDS12032.
- Auditive feedback on touch
- by default the AURUS-TFT will give a click every time a button is pressed. When preferred, this can be switched off.
- Motion detection feedback on IR LED
- indicates that the IR LED of the TDS12025 will be on when motion is detected.
Compatibility list:
| Setting | TDS12019 AURUS-1 | TDS12020 AURUS-2 | TDS12024 AURUS-4S | TDS12021 AURUS-4XL | TDS12026 AURUS-4 TEMP | TDS12022 AURUS-OLED | TDS12032 AURUS-OLED PLUS | TDS12025 AURUS-2 SENSE | TDS12064 AURUS-TFT |
| Orientation | NA | V | NA | V | NA | V | NA | V | NA |
| (OLED) Display OFF after | NA | NA | NA | NA | V | V | V | NA | V |
| Display Brightness | NA | NA | NA | NA | NA | NA | NA | NA | V |
| Feedback LED’s ‘ON’ brightness | V | V | V | Ver. 10 | V | Ver. 20 | V | V | NA |
| Feedback LED’s ‘Night illumination’ | V | V | V | Ver. 10 | V | Ver. 20 | V | V | NA |
| Feedback LED’s OFF when OLED if OFF | NA | NA | NA | NA | V | V | V | NA | NA |
| Auditive feedback on touch | V | Ver. 4 | V | Ver. 10 | V | Ver. 27 | V | V | V |
| Motion detection feedback on IR LED | NA | NA | NA | NA | NA | NA | NA | V | NA |
Built-in temperature sensor.
The AURUS-1, AURUS-2, AURUS-2 SENSE, AURUS-4S, AURUS-4XL, AURUS-4 TEMP, AURUS-OLED and AURUS-OLED PLUS contain a built-in temperature sensor. This can be used as sensor zone through the complete Domotics project.
The built-in temperature sensor isn't activated by default. To activate, follow the following instructions:
- Click on the temperature sensor icon
- Choose 'AURUS Temperature sensor' as ‘Sensor Type’ and give the sensor a proper name: e.g.: Sensor AURUS-OLED Living.
- If the sensor will be used to control a heating/cooling system, complete the settings at 'Output properties:
;){kind=link}